Tuesday, April 16, 2013

DIY Corkboard Map Tutorial

Hey Y’all! I thought I’d share my first EVER DIY post. I am very skeptical of DIY posts as I am a terrible teacher. Just ask anyone who has ever asked me a question. Seriously, it is just easier if I do it for them. Hopefully you’ll all be able to make your very own Cork board map. Like this one below. I found some like these on ETSY and a few other sites, but they were soooo expensive. Who wants to pay 50 bucks for a 12” x 18” map?! Not me!! My map only costs about $15.00 and it is 20” x 30”!

 

Supplies:

·         24x36 cork tile – Mine came from Hobby Lobby, it was only $16.99 and I used the 40% off coupon.
·        Dremel Rotary Tool- If you don’t have one hopefully you can borrow one!
·        Hot glue gun & glue sticks
·        2 Picture hanging backs (They look like shark teeth)
·        Ribbon ½” thickness– About 1-1.5 yards
·        Tracing paper
·        Sharpie (any color- I used black)
·        Ball point pen or mechanical pencil
·        Scissors
·        Tape
·        Straight Pins
·        PowerPoint map or large wall map would also work.

If you don’t have Microsoft PowerPoint you can purchase a paper map and cut it out. If you do have access to PowerPoint this is how you can print your own map template. The first thing you need to do is find a picture of the continental USA or whatever country you wish to create. Hawaii & Alaska meant more cutting so I axed them from the plan. You can simply Google “USA Map png” and tons will show up. Find one that you like, preferably with all the states outlined and save it.

 
Creating Your Map Template

·        Create a new presentation in PowerPoint.
·        Click the DESIGN tab and open PAGE SETUP.
·        Change the Width to 30 inches and the Height to 20 inches and press OK.
·        Insert your saved map picture.
·        Scale the Map Picture to fit inside your slide.
·        Go to the FILE tap and press PRINT.
·        Under PRINTER press PRINTER PROPERTIES.


·        Scroll under PRINTING SHORTCUTS until you find POSTER PRINTING and click.
·        Under POSTER PRINTING pull down the drop down menu to select 3x3 (9 sheets).
·        Click OK and then click PRINT.

This should print your 9 paged map that you’ll then cut and tape together. One you have your map pieced together you are ready to ROLL!

 
Lay out your cork board and pin your map in place. Take your sharpie and outline the map onto the cork board.  *TIP: I didn’t worry about any outlying islands or crazy cuts. Remember you’ll be cutting this with a power tool, so make it easy on yourself!

Once you’ve got your map outlined, remove the pins and put the map to the side. This is where the dirty work occurs. I would suggest that you should cut your cork board outside; however, I was hardheaded and it was cool outside so I put down a sheet to protect my living room from sawdust. Slowly and cautiously begin cutting out your map. *TIP: Please follow all safety precautions listed in your Dremel User Guide.

 Jacob took this picture. Notice his finger over the camera?


Once you’ve got your cork map cut out you should sand your edges. At least clean them up a bit. I then took the map outside to use a handheld broom and brushed all excess dust from the map. *TIP: Florida, Maine, Michigan and Texas are pretty fragile. DO NOT HANDLE just those states or you’ll need additional hot glue. . .


There she is, all cut and ready to be cleaned!

 This evil cat was "helping", if by helping I mean rolling/walking in the saw dust and tracking it ALL over the house. . .
Told ya it makes a mess! Thank goodness for the sheet we laid down to catch the dust!

 
The map all cleaned and ready to be traced.

If you don’t plan on tracing the states you can skip this step. Place your tracing paper over the cork. Place the paper map on the top of the tracing paper. Make sure the paper map and the cork map are aligned before pinning the paper map and the tracing paper in place. Use the ballpoint pen or pencil with no lead to trace around all the states. *Tip: If you can’t remember if you’ve traced the state, trace it again just in case.

 

The state lines from the tracing paper.
 

Once you’ve traced all the states remove the paper map and tracing paper and make sure the entire map transferred. If it did, GREAT JOB, if not, re-trace what needs to be traced. Once all the states are visible, use the sharpie to trace over the graphite lines and around the edges of the map.

The map with the lines drawn in sharpie!

Hot glue the picture hangers on the back. You’ll want to make sure the ribbon will not cut across any of the fragile land masses (MI, WI or MN). Hang that awesomely cheap and awesomely cute map up and get to traveling! We are only pinning places that we have travelled together. I plan on painting a canvas with a cute travel quote, but I'll add that later.

 
Have a great week readers!

1 comment:

  1. You did a great job on this! The materials are definitely cheap, but considering the amount of work that goes into making this, I think $50 is a reasonable price.

    ReplyDelete